Aidan's loose oily bunghole actually runs a track lap
#6721
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Oh, also started profiling the trunk lid to draw up a spoiler. String stapled to the walls level across the trunk lid. Will allow me to take measurements all the way across.
Current plan is to design it something like this
With 2-4 triangles for support, and rubber stripping to allow for adjustability even on the curve.
Current plan is to design it something like this
With 2-4 triangles for support, and rubber stripping to allow for adjustability even on the curve.
#6722
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Anyone have suggestions for how to raise the brake pedal? I adjusted it all the way up and it still drops just below the gas pedal when braking, just enough to make heel toe a little hard.
Bend it up? Add some sort of pedal on top?
Bend it up? Add some sort of pedal on top?
#6723
My first thought is that there is air in the system.
My second thought would be to put a spacer on the pedal at first to figure out "how much" the pedal needs to come out to be where you want, then cut/weld a new pedal to put it in that position without spacers.
#6724
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Pedal feel is good. similar to other pedals. I've bled A LOT of fluid (stupid idea to do a fresh system bleed with ATE, using cheap fluid next time).
I have the 929 1" master so travel should be ok. I think it has to do with the gas pedal (FM pedal).
Also wouldn't be too hard to just bolt a spacer to it similar to the FM pedal extension.
I have the 929 1" master so travel should be ok. I think it has to do with the gas pedal (FM pedal).
Also wouldn't be too hard to just bolt a spacer to it similar to the FM pedal extension.
#6725
I guess you've seen Blackbird Fabworks (Moti)'s spoiler? I imagine you can do it cheaper, but it's adjustable and people seem to like it. Check to see how flat your string is, it should have an arc to it, hung like that. It takes one to know one and all that.
I'm glad I cleaned up the edges on the cam wheel - you took a decent pic.
Anyway, the cam wheel's purpose is 3-fold:
1) People who push these cars typically have a failure of the cam sensor (due to heat - though if it's engine or electrical is unknown) - this allows switching to a more modern sensor
2) This gives ~2x (possible 4x, depending on the current ECU code in use) on VVT phasing updates, and should keep the cam control tighter
3) Using "poll level", you get rid of all the weird work around for the miata in the MS codebase. This allows the engine to know where it is in half the time, running full sequential faster/better, and starting faster. When combined with a high tooth count crank trigger it should improve overall timing accuracy significantly.
At least it works on my car. :-)
I'm glad I cleaned up the edges on the cam wheel - you took a decent pic.
Anyway, the cam wheel's purpose is 3-fold:
1) People who push these cars typically have a failure of the cam sensor (due to heat - though if it's engine or electrical is unknown) - this allows switching to a more modern sensor
2) This gives ~2x (possible 4x, depending on the current ECU code in use) on VVT phasing updates, and should keep the cam control tighter
3) Using "poll level", you get rid of all the weird work around for the miata in the MS codebase. This allows the engine to know where it is in half the time, running full sequential faster/better, and starting faster. When combined with a high tooth count crank trigger it should improve overall timing accuracy significantly.
At least it works on my car. :-)
#6726
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Not trying to copy another design. But create a new one. I like the simplicity of this. Its one piece, adjustable, and should be cheap.
Also I couldn't find poll level. Waiting for your full instructions.
Also I couldn't find poll level. Waiting for your full instructions.
#6733
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Props to 949Racing for probably the fastest customer service email I've ever received. (<1 min reply) For some reason I had it in my head that the studs in the 949 Billet tophats were press in. But it turns out they are just bolts.
Got some longer bolts and put my ghetto master cylinder brace on.
Got some longer bolts and put my ghetto master cylinder brace on.
#6735
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Its perfect. It will wear away and then meet up flat.
Bolt is just a test. I will be replacing it with one of those leveling mount feet thingies.
This thingy
http://www.mcmaster.com/#6301K72
Bolt is just a test. I will be replacing it with one of those leveling mount feet thingies.
This thingy
http://www.mcmaster.com/#6301K72
#6738
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Finally got around to switching to new deadtimes. Pulled about 5% fuel from the whole table, and that put my boost AFR right around 11.5-2, just where I like it. Then autotune pulled assloads of fuel from non-boost areas.
Log review plz. This is my track boost level. Max boost around 133kpa (~5psi).
AFR's are around 13. I feel like this is too lean for boost. Going to try and add some more fuel to get them closer to 12.
Log review plz. This is my track boost level. Max boost around 133kpa (~5psi).
AFR's are around 13. I feel like this is too lean for boost. Going to try and add some more fuel to get them closer to 12.
#6739
SADFab Destructive Testing Engineer
Thread Starter
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Nobody? My gauge reads over a point richer than TS. So I got the gauge belo 12 for everywhere in boost. But TS is still reading above 12. Need to get my tinyiox in and get digital AFR.