Quiet you. I shall reveal when all is complete.

Anyone else have an Evolution Rage2 chop saw? I have made ~40 cuts in steel tube between .065 and .095 wall. The cuts are super clean, and the chips are somehow not sharp. The only thing I don't like is the miter gauge clamp combo which had a tendency to wander between cuts.

This is the saw: Evolution Power Tools 14 in. Multi-Purpose Chop Saw-RAGE2 - The Home Depot

I think I can improve the miter gauge by loosening the bolts that hold the saw, then adjusting the saw blade angle until it is square with the 45 and 90 stops on the clamp bracket. Right now if I adjust the bracket to the end of its travel (indicated at 45 or 90) the cut is off by a few degrees. Not having support from the end of the bracket travel is probably contributing to the miter setting wandering.

Are you still using the blade it came with? Which is this one (I think): RAGE 14 in. Multipurpose Replacement Blade-RAGE355BLADE - The Home Depot

I've been looking for a 'reasonably' priced, non-abrasive blade for mild steel... looks like this might fit the bill if you're getting clean cuts and good life out of it.

I've got one. The blade killer IS the clamping. If anything moves during the cut, you're at risk of catching a carbide tip and losing it. It seems to go downhill after that. IMO the best approach is to buy two different blades specific to the metal rather than the all-in-one. I'm considering picking up an HF circular sharpener at this point to reclaim some of these worn Rage blades. Though the HF sharpener seems to have similar issues with precision while sharpening.
3/16" tube for motormounts:
http://fe3miata.com/site/wp-content/...unts-2-720.jpg
http://fe3miata.com/site/wp-content/...unts-3-720.jpg

I am still using the blade that came with it and am probably over 60 cuts now. My carbide tips show no signs of wear.
https://cimg3.ibsrv.net/gimg/www.mia...c6de3f8806.jpg



The clamp has a few design flaws, the rounded edge of the corner of the angle stock doesn't do a great job holding small tubing down close to the base. I have been putting a little bit of downward hand pressure on the tubing as I tighten the clamp.

They sell a much more expensive saw for cutting steel. Also a 14" chop saw, but the base and clamp look like a better design. At $400ish for their steel cutting saw, there are plenty of other options for similar chop saws from other manufacturers.

I was hoping to retrofit a laser line onto the saw but I can't find one for a 1" arbor. That would really help with cut accuracy and the less than perfect clamping. I have 100lb of steel showing up today and I am going to build a rolling chop saw stand with a sliding out feed measuring stop.

I've been using a slightly beefier one of those, the clamp is terrible and is on my list of things to fix. The sliding clamp jaw isn't tight on the table and will rock when cutting weird material shapes. I swap blades for aluminum and steel, but if I remember right I counted more teeth on the steel blade, that doesn't really make much sense to me. Someone who isn't me tried to cut a too small piece that decided to let loose, lost a lot of carbide that day. Still buzzes through aluminum halfway decently though.

Evolution EVOSAW380 Raptor 15" TCT Steel Cutting Saw, Includes 14BLADEST Blade | Toolfetch

My new clamp block will have some sort of adjustable stop for making multiple repeated cuts, something else I wish this thing had. The saw blade will flex on the arm a bit which makes swinging it down and measuring and trying to nail repeated finish cuts an exceptional pain in the ass. If I had a fixed stop I could load the thing against one side and just chop, chop, chop. Now I've got to pull it one way, down, measure, adjust, clamp, measure, unclamp, adjust. Fucking sucks...

I've cut down many full solid bars of aluminum and 304 with the thing after I initially just laughed at it. Not perfect out of the box but still really impressive for less than $300.

I am planning to do something like this crude sketch:
https://cimg7.ibsrv.net/gimg/www.mia...146970bb83.png


Then attach a measuring tape to the sliding part so I can quickly get accurate numbers. It will only work for straight cuts though.

I wish I had the room for a table like that because it'd work perfect, hopefully we'll be moving to a bigger shop next year. I have clamped it down to the welding table for a base to clamp stops on, it usually takes more time to clear the table than freehanding a few cuts lol.


I just looked at the specs on the thing and I apparently shouldn't be cutting solid bar like I am, though it does do it. I've cut at least 20 cuts in 1-1/4" and 1" square 303, each. Still wish we had room for a proper bandsaw though...

Ive just build 25 of these, USD is pretty damned strong compared to ours (75 cents), do you reckon anyone here would be interested?

https://scontent-lax3-1.xx.fbcdn.net...25&oe=5800FAF3

https://scontent-lax3-1.xx.fbcdn.net...25&oe=5808B9DD

https://fbcdn-sphotos-e-a.akamaihd.n...f069a452f07ed0

https://fbcdn-sphotos-e-a.akamaihd.n...a3ccf452f6d123

https://scontent-lax3-1.xx.fbcdn.net...78&oe=57FFBD6E

https://fbcdn-sphotos-g-a.akamaihd.n...ce97dee81d5d3d

https://scontent-lax3-1.xx.fbcdn.net...65&oe=57E9DD27

Those look pretty sweet. I might be interested.

Wow very impressed with this thread. lots of gold in here. super glad i joined this forum now haha.

Whats the inside look like?

Second that can we get some inside picture and what's the full benefits if you don't mind me axing

Some info here:

https://www.miataturbo.net/engine-pe...d-78293/page8/

Its got a chamber per AN port, with a 5mm wide vertical slot joining the chambers with SS wool filling.

Dann

My concern with your catch can location is that with a Begi/FM manifold there might be fitment issues. Those are the majority of manifolds in the US so it might be limiting.

Got a picture from the front of the rail looking back?

I don't right now and I am out of town at the moment. I do know that is the part of the shelf that you have to cut/bend back to fit with the Begi/FM manifolds. I may be able to get you some pictures later this week.

Thankyou

It could go in front of it though since most of us don't have that stupid power steering res. stole a pic from random googlin

http://www.bellengineering.net/image...8_osN2Kj68.jpg

Would potentially be interested depending on price.