Right, did you re-setup your project per my inctructions above?

 

Yes and that's the error I got

 

Ok, go to the boost control menu (Advanced -> Boost control settings) and switch it off. Hit Burn, switch off the ignition off for 5 seconds and then back on - does the message go away?

 

Yes! If this fires up I will squeal like a little school girl

 

The config error went away but it still won't start. Also looking at the gauge cluster on tuner studio the arf is different then whats showing on the gauge

 

Looks like the map you uploaded is totally screwed up - PM me your email address and I'll send you a new map. Which injectors do you have installed?

 

He's using RX8 yellows. (425cc) 7.45 required fuel I do believe.

 

Would the required fuel be set up for 425cc or 500cc because of the higher pressure the newer cars run at?

 

What wideband are you using? If it's LC1, you probably don't have the outputs on that set correctly (cannot be done with and has nothing to do with tuner studio).
The wideband reading difference would also have nothing to do with it not starting.

 

New map sent - the proper flow to use is 488cc@60psi.

 

This is off topic, and I don't mean to thread Jack, but what whp do you think those injectors would max out at with that fuel pressure?

 

Thank you so much Rev. And I wired the sideband wire to the wire reverant told me too so I thought it would work..

 

Probably around 280-290 crank hp at 90% duty cycle.

 

What I meant is in the lc1 software you need to have it setup a certain way...it's software issue not the physical connection...
Let me get off my phone and get on my pc and upload a photo.

 

Using RC engineerings calculator it looks like 500cc's will flow enough for 300 at the crank

 

Ah I see. Uploaded the new map this is what I got.
17 Warnings:
Warning: MSQ Units Mismatch for egoTemp! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for tempTable! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for clt0! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: Parameter in msq, but not valid for current firmware: No options found for Bit EcuParameter:tempUnits
Warning: MSQ Units Mismatch for IdleHyst! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fastIdleT! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for IACcoldtmp! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for mat0! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_crank_clt_temps! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for matCorrTemps! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for pwmidle_clt_temps! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for temp_table_p5! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for fc_clt! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for matTemps! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for N2OClt! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for idleadvance_clt! °F found in current configuration, �F found in MSQ, values were not converted to new units.
Warning: MSQ Units Mismatch for RevLimLookup! °F found in current configuration, �F found in MSQ, values were not converted to new units.

 

Ignore, proceed to start the car.

 

Well? Did it fire up?

 

It either blew up and killed him or he died from excitement because it actually started.

 

Lol!!!!