Impuls build
#161
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
Odd, I bought direct from amsoil before.
Thought I did buy the preferred membership as well. (good discount of 25%, paid for more than itself on my one purchase of engine oil, transmission fluid and diff fluid)
AMSOIL Preferred Customer Registration
Thought I did buy the preferred membership as well. (good discount of 25%, paid for more than itself on my one purchase of engine oil, transmission fluid and diff fluid)
AMSOIL Preferred Customer Registration
Couldn't see the sparks in the video.
Your ignition may be in need of servicing, but the reality is that a healthy MSM ignition is capable of supporting more power than the MSM turbo will put out.
Now, knowing that you're using a stock MSM turbo, your power numbers don't look bad.
Your ignition may be in need of servicing, but the reality is that a healthy MSM ignition is capable of supporting more power than the MSM turbo will put out.
Now, knowing that you're using a stock MSM turbo, your power numbers don't look bad.
I was thinking maybe I'd be in the 220 range or even 230 being generous. Thought spark isn't fine tuned. I need to get a knock sensor and shielded audio cable to wire up my det can.
I also need a manifold, turbo, and exhaust :/ all pretty expensive things. But then I should be able to make ALLOFIT
#164
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
But I think sparking in the engine bay takes priority too.
I really do think you are right thought I'd like my gauge cluster to work as it did before I just have no idea what's wrong and I don't know where the grounding point is for it, to check if it's that. (Since the car did sit for nearly a year.)
#165
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
Oh, for those that are interested.
The EFR7163 started shipping out last week.
Geoff has a single scroll vband EWG he offered me. I asked if any are twin yet. waiting on reply.
Though I want IWG, BUT Ehh not like I have the cash now anyways
The EFR7163 started shipping out last week.
Geoff has a single scroll vband EWG he offered me. I asked if any are twin yet. waiting on reply.
Though I want IWG, BUT Ehh not like I have the cash now anyways
#166
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
Waiting on my Hawk blue pads still :/ were suppose to be here last week with the front hubs. Thanks planetmiata.
I got my new rotors, axle nuts, Amsoil DOMINATOR grease, and rear bearings.
Waiting on front spindle nuts too.
Anyone have a T3 turbo they don't want anymore?
I got my new rotors, axle nuts, Amsoil DOMINATOR grease, and rear bearings.
Waiting on front spindle nuts too.
Anyone have a T3 turbo they don't want anymore?
#169
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
what happens when you dyno in 4th on a 6speed.
I'm not exactly sure how everything works with a dyno but shouldn't they need to know you're final drive and transmission gearing? Maybe someone can shed light on it for me besides me just talking to myself.
I go very rich after 5000, since I added fuel for safety I felt like something wasn't right while driving it. So they let me pull some fuel out (I only did a little) and this made the max run.
I guess I should just shift at 5250rpm I suppose.
I'm not exactly sure how everything works with a dyno but shouldn't they need to know you're final drive and transmission gearing? Maybe someone can shed light on it for me besides me just talking to myself.
I go very rich after 5000, since I added fuel for safety I felt like something wasn't right while driving it. So they let me pull some fuel out (I only did a little) and this made the max run.
I guess I should just shift at 5250rpm I suppose.
#171
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
Oh, do I ever.
I did some WOT pulls today with the rev limiter set to 7200, and I couldn't pass 6300 at 100% so I dropped throttle position and got close to 7000. I was running very rich. I think it was just a huge wall since my VE table with this small turbo looks stupid.
Spikes to 80 @ 4500-5000rpm then quickly tapers to 67's but still rich. Normal?
This was the dyno run that made the most, even after heat soaking.
184rwhp 196ft/lbs
I did some WOT pulls today with the rev limiter set to 7200, and I couldn't pass 6300 at 100% so I dropped throttle position and got close to 7000. I was running very rich. I think it was just a huge wall since my VE table with this small turbo looks stupid.
Spikes to 80 @ 4500-5000rpm then quickly tapers to 67's but still rich. Normal?
This was the dyno run that made the most, even after heat soaking.
184rwhp 196ft/lbs
#173
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
I'm thinking it may have something to do with the electronics ( gauge cluster ) going ape **** at anything above 5500rpm
#174
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
****, I forgot to check that plug.
Well I'm starting this week full time at my new job ( lame pay compared to my military paychecks ) so I haven't had the time to do a lot with the car, still waiting on the front spindle nuts. I think they are at the post office just don't have time to get them till Friday.
After work yesterday I I found that the axle I have in my trunk hit loose my positive battery terminal and spun it to where it made contact with the battery tie down causing an intermittent short that made the car jerk and all sorts of scary **** when it hit bumps it anything. This was very frustrating add I was in the middle of 5 o'clock downtown Tampa traffic abd I absolutely HATE traffic. So when I git on a road known as bayshore ( it follows Tampa bay to the south point being Macdill AFB) the car started jerking and hesitating very badly ( horrid rough roads) So what did my pissed off self do? I stabbed the gas heard a chunk of everything in my trunk and stared drifting around 2 bends with what seemed like good transitions but probably looked probably like the same as a Honda song a reverse-forward burnout. But now I have cord showing very badly on my tires so I ordered a new set to daily on.
tl;dr
Car act funny, jimmies rustled, sweet jdm drifto
I'm looking to get a cheap turbo to get me to 300 or more now(ultimate goal of breaking 400hp pump gas miata with EFR still there just need the job to pay for it). So I may enter the curio churbro leagues.
After taxes my fab guy gets a tig and REALLLY wants to do my hotside bits.
Hopefully he takes sexual advances at payment.
Well I'm starting this week full time at my new job ( lame pay compared to my military paychecks ) so I haven't had the time to do a lot with the car, still waiting on the front spindle nuts. I think they are at the post office just don't have time to get them till Friday.
After work yesterday I I found that the axle I have in my trunk hit loose my positive battery terminal and spun it to where it made contact with the battery tie down causing an intermittent short that made the car jerk and all sorts of scary **** when it hit bumps it anything. This was very frustrating add I was in the middle of 5 o'clock downtown Tampa traffic abd I absolutely HATE traffic. So when I git on a road known as bayshore ( it follows Tampa bay to the south point being Macdill AFB) the car started jerking and hesitating very badly ( horrid rough roads) So what did my pissed off self do? I stabbed the gas heard a chunk of everything in my trunk and stared drifting around 2 bends with what seemed like good transitions but probably looked probably like the same as a Honda song a reverse-forward burnout. But now I have cord showing very badly on my tires so I ordered a new set to daily on.
tl;dr
Car act funny, jimmies rustled, sweet jdm drifto
I'm looking to get a cheap turbo to get me to 300 or more now(ultimate goal of breaking 400hp pump gas miata with EFR still there just need the job to pay for it). So I may enter the curio churbro leagues.
After taxes my fab guy gets a tig and REALLLY wants to do my hotside bits.
Hopefully he takes sexual advances at payment.
Last edited by Impuls; 12-17-2013 at 09:15 PM.
#176
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
This is true, I don't want anything to go wrong, When I get the time too troubleshoot the little things I will.
Anyone happen to have a 99 or 04msm knock sensor
or know if they work any good as an detcan? I'd like to not have to install and uninstall one every time it needs tuned, plus I need a new knock sensor.
Anyone happen to have a 99 or 04msm knock sensor
or know if they work any good as an detcan? I'd like to not have to install and uninstall one every time it needs tuned, plus I need a new knock sensor.
#177
Yeah, I remember that from when I first got the engine running. I don't believe it is but I'd have to check again. I thought with it connected you can't even go +5000rpm. I know I have the vac for the butterflies disconnected.
I'm thinking it may have something to do with the electronics ( gauge cluster ) going ape **** at anything above 5500rpm
I'm thinking it may have something to do with the electronics ( gauge cluster ) going ape **** at anything above 5500rpm
What's the reasoning here? Mine still runs it. We did have a problem when the polarity was reversed on the plug, though.
#178
This is true, I don't want anything to go wrong, When I get the time too troubleshoot the little things I will.
Anyone happen to have a 99 or 04msm knock sensor
or know if they work any good as an detcan? I'd like to not have to install and uninstall one every time it needs tuned, plus I need a new knock sensor.
Anyone happen to have a 99 or 04msm knock sensor
or know if they work any good as an detcan? I'd like to not have to install and uninstall one every time it needs tuned, plus I need a new knock sensor.
#179
Senior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2012
Location: Tampa, FL
Posts: 754
Total Cats: 19
Do you have a MSM engine with VTCS but running a 99-00 MS? That's what we're talking about I do believe.
So you're saying you just changed the polarity on = 1 off = 0 to on = 0 off = 1, like that? Or was it actually in the plug wiring
_____
Thanks vlad, I'd like to run ms with the knock sensor even though ms2's knock abilitys are nothing to write home about compared to ms3, but I also want a detcan I can install and use at any time.
Suggestions on the sensor to use for detcan? I have that harbor freight stethoscope, I was thinking it's some bosch with the right thread size.