EPIC nuts/studs loosening thread (reposting stupid stuff without reading = warning)
#845
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
I want to do one more test, with safety wire as a mechanical locker. That way the only failure mode is creep/stretch. If it doesn't work, I'll drop the grade and we can discuss whether a second test on a second alloy is worth doing.
#847
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,100
I don't have a crow's foot, but I was sure to keep it light, under 10 ft.lbs for everything. Studs into the manifold, then nuts onto the studs. That's the right way to go for material expansion, and the WRONG way to go for keeping the fasteners in. If you use light torque, you've got to have something holding them in - safety wire, Stage 8s and roll pins in the studs, something.
Last edited by Savington; 10-04-2009 at 01:02 AM.
#848
I don't have a crow's foot, but I was sure to keep it light, under 10 ft.lbs for everything. Studs into the manifold, then nuts onto the studs. That's the right way to go for material expansion, and the WRONG way to go for keeping the fasteners in. If you use light torque, you've got to have something holding them in - safety wire, Stage 8s and roll pins in the studs, something.
#849
2 Props,3 Dildos,& 1 Cat
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
I don't have a crow's foot, but I was sure to keep it light, under 10 ft.lbs for everything. Studs into the manifold, then nuts onto the studs. That's the right way to go for material expansion, and the WRONG way to go for keeping the fasteners in. If you use light torque, you've got to have something holding them in - safety wire, Stage 8s and roll pins in the studs, something.
but wasn't the point of "unobtanium" studs that you could torque them normally and they'd still do well with the thermal expansion?
#850
I don't see how 10ft.lbs will ever stay on without additional Resbond, sport weld or whatever. Any 10ft.lbs nut on track will be gone before I re-enter the pits, let alone the turbo to manifold nut. Also, 10ft.lbs won't even overcome material imperfection, like drops of ceramic coating, rust, debries.
Then how do you explain my **** is still tight? After I tightened the nuts as good as I could with a wrench, they were spot welded.
Then how do you explain my **** is still tight? After I tightened the nuts as good as I could with a wrench, they were spot welded.
#851
Sav: try flange nuts with Resbond on SS or Inconel. Rebond on studs, insert and let them dry. Then mount turbo and tighten nuts, let them dry too. 24hrs before you even start the engine. Tighten the nuts pretty good. Flange nuts take well over 10ft.lbs Basically, then you've got what I've got, minus spot welds.
#852
I don't see how 10ft.lbs will ever stay on without additional Resbond, sport weld or whatever. Any 10ft.lbs nut on track will be gone before I re-enter the pits, let alone the turbo to manifold nut. Also, 10ft.lbs won't even overcome material imperfection, like drops of ceramic coating, rust, debries.
Then how do you explain my **** is still tight? After I tightened the nuts as good as I could with a wrench, they were spot welded.
Then how do you explain my **** is still tight? After I tightened the nuts as good as I could with a wrench, they were spot welded.
I can't explain anything, you've got the real world right there on your manifold. All I have is numbers. Testing tells the real deal, and for your application it worked. End of story.
If the studs are plastically deforming on sav's manifold and not simply just spinning off though, less preload will help.
#853
I guess you don't DD the car? 4 Laps seems like the sort of thing that might show up on the street if you're even half the ******* I am. :-) I can't say how well my set up would work on the track, but I can say there's a definitely 50:1 improvement in whatever I have now from the 6-8 combinations I tried before it.
Can you tell if the nuts moved at all?
Can you tell if the nuts moved at all?
#856
Try and get the measurements with some caliperss and compare the average of the unused studs to the Used studs and then measure the threads and the shank Im truly interested,I think what might be happening is the manifold is heating up faster than the stud allowing the threads to pull out of the casting.I couldnt immagine that even low alloy inconel would creep that much at the temps you are generating.
-G-
-G-
#858
As soon as my car is done,I need to find some way of flogging the living hell out of it to see what my bolts will hold like.3/8"-24 shoulder bolts 316 ss.1/8" thick 316 washers mechanical locknuts,safty wired heads.Going to torque down to 45 ft.lbs.,manifold flange is 9/16" thick 1018 steel.Low mount design with heim joint brce to engine block from turbo.I need a camera to doc. this stuff as it gets built.
-=G=-
-=G=-